Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 4 (1923)

Compiled by Timothy Edwards


 
 
Outfit 4 (1923)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 12
2 Perforated strip 5 1/2" 11hole 21
2a Perforated strip 4 1/2" 9hole 2
3 Perforated strip 3 1/2" 7hole 6
4 Perforated strip 3" 6hole 6
5 Perforated strip 2 1/2" 5hole 18
6a Perforated strip 1 1/2" 3hole 2
8 Angle girder 12 1/2" 25hole 8
9 Angle girder 5 1/2" 11hole 4
10 Flat Bracket (Fishplate) 8
11 Double Angle Bracket 5
12 Angle bracket 22
12a Angle bracket 1x1" 4
13 Axle rod 11 1/2" 2
13a Axle rod 8" 1
14 Axle rod 6" 3
15 Axle rod 5" 4
15a Axle rod 4 1/2" 5
16 Axle rod 3 1/2" 5
17 Axle rod 2" 5
18a Axle rod 1 1/2" 4
19 19s/19hCrank Handle - (length varied 3 1/2" - 5") 2
19b Pulley 3" dia, 1
20 Flanged wheel 1 1/8" dia 8
21 Pulley 1 1/2" dia 1
22 Pulley 1" dia 4
22a Pulley 1" dia without boss 3
23 23bPulley 1/2" dia without boss - metal 3
24 Bush wheel 1 3/8" dia, 8 holes 2
26 Pinion 1/2"dia, 1/4"face, 19t 2
27a Gear wheel 1 1/2"dia,57t 1
28 Contrate Gear 1 1/2" dia, 50t 1
29 Contrate Gear 3/4" dia, 25t 2
32 Worm Gear 1
33 Pawl (type 2) with Pivot Bolts 1
34 Spanner 2
35 Spring clip 18
36 Screwdriver - Standard Bent Rod 1
37 Square Nut and bolt (bolt 5/16" long) 130
38 Washer 3/8" dia. 24
40 Hank of cord 4
43 Tension Spring 2" 1
44 Cranked bent strip 1
45 Double bent strip 3
46 Double angle strip 2 1/2x1" 2
48 Double angle strip 1 1/2x1/2" 2
48a Double angle strip 2 1/2x1/2" 10
48b Double angle strip 3 1/2x1/2" 6
48d Double angle strip 5 1/2x1/2" 2
52 Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) 2
53 Flanged plate 3 1/2x2 1/2" 5
54 Flanged sector plate 4" 3
57 Wire Hook 1
59 Collar 10
61 Windmill sail 4
62 Crank 2
63 Coupling 6
65 Centre fork 1
77 Trangular plate 1" 2
90 Curved strip 2 1/2", 2 3/8"r 4
94 Sprocket chain 3ft
95 Sprocket wheel 2"d, 36t 1
96 Sprocket wheel 1"d, 18t 2
98 Braced girder 2 1/2" 5hole - double open 1
99 Braced girder 12 1/2" 25hole -double open 4
100 Braced girder 5 1/2" 11hole - double open 6
103f Flat girder 2 1/2" 5hole 2
108 Architrave (Corner Gusset) 2
109 Face plate 2 1/2"d 1
111 Bolt 3/4" 3
115 Threaded pin - Round Shoulder 2
116 Fork piece, Large 1
125 Reverse angle bracket 1/2" 4
126a Flat trunnion 4
130 Eccentric, Triple Throw 2
134 Crank shaft 1" stroke 1

NOTES

1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.

2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.