Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 6 (1922-23)

Compiled by Timothy Edwards


 
 
Outfit 6 (1922-23)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 48
1a Perforated strip 9 1/2" 19hole 2
2 Perforated strip 5 1/2" 11hole 50
2a Perforated strip 4 1/2" 9hole 4
3 Perforated strip 3 1/2" 7hole 18
4 Perforated strip 3" 6hole 24
5 Perforated strip 2 1/2" 5hole 36
6 Perforated strip 2" 4hole 24
6a Perforated strip 1 1/2" 3hole 14
8 Angle girder 12 1/2" 25hole 24
8a Angle girder 9 1/2" 19hole 4
9 Angle girder 5 1/2" 11hole 16
9d Angle girder 2 1/2" 5hole 1
10 Flat Bracket (Fishplate) 16
11 Double Angle Bracket 16
12 Angle bracket 80
12a Angle bracket 1x1" 4
12b Angle bracket 1x1/2" 2
13 Axle rod 11 1/2" 4
13a Axle rod 8" 4
14 Axle rod 6" 4
15 Axle rod 5" 4
15a Axle rod 4 1/2" 5
16 Axle rod 3 1/2" 5
16a Axle rod 2 1/2" 2
17 Axle rod 2"# 5
18a Axle rod 1 1/2" 4
19 19s/19hCrank Handle - (length varied 3 1/2" - 5") 3
19a Spoked Wheel 3", with boss 4
19b Pulley 3" dia, 2
20 Flanged wheel 1 1/8" dia 8
21 Pulley 1 1/2" dia 2
22 Pulley 1" dia 5
22a Pulley 1" dia without boss 4
23 23bPulley 1/2" dia without boss - metal 8
24 Bush wheel 1 3/8" dia, 8 holes 5
25 Pinion 3/4"dia, 1/4"face, 25t 2
26 Pinion 1/2"dia, 1/4"face, 19t 6
27 Gear wheel 1 1/4"dia, 50t 1
27a Gear wheel 1 1/2"dia,57t 3
28 Contrate Gear 1 1/2" dia, 50t 2
29 Contrate Gear 3/4" dia, 25t 2
32 Worm Gear 2
33 Pawl (type 2) with Pivot Bolts 1
34 Spanner 2
35 Spring clip 24
36 Screwdriver - Standard Bent Rod 1
36a Screwdriver - Extra Long (wooden handle) 1
37 Square Nut and bolt (bolt 5/16" long) 300
38 Washer 3/8" dia. 30
40 Hank of cord 6
41 Propeller Blade - type 1 (wide) 4
43 Tension Spring 2" 2
44 Cranked bent strip 1
45 Double bent strip 8
46 Double angle strip 2 1/2x1" 4
50 Eye piece without boss 2
52 Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) 7
52a Flat plate 5 1/2x3 1/2" 2
53 Flanged plate 3 1/2x2 1/2" 8
53a Flat plate 4 1/2x2 1/2" 1
54 Flanged sector plate 4" 4
57 Wire Hook 2
57b Loaded Hook (large) - ball type 1
58 Spring cord 40" 1
59 Collar 18
60 48aBent strips 2 1/2" 16
60a 48Bent strips 1 1/2" 2
60b 48bBent strips 3 1/2" 6
60c 48dBent strips 5 1/2" 7
61 Windmill sail 4
62 Crank 3
62a Threaded Crank 1
63 Coupling 9
65 Centre fork 1
70 Flat plate 5 1/2x2 1/2" 3
72 Flat plate 2 1/2x2 1/2" 2
76 Trangular plate 2 1/2" 1
77 Trangular plate 1" 2
80a Screwed rod 3 1/2" 1
81 Screwed rod 2" 1
89 Curved strip 5 1/2", 10"r 4
90 Curved strip 2 1/2", 2 3/8"r 6
94 Sprocket chain 8ft
95 Sprocket wheel 2"d, 36t 3
95a Sprocket wheel 1 1/2"d, 28t 1
96 Sprocket wheel 1"d, 18t 4
96a Sprocket wheel 3/4"d, 14t 1
97 Braced girder 3 1/2" 7hole - double open 4
98 Braced girder 2 1/2" 5hole - double open 8
99 Braced girder 12 1/2" 25hole -double open 8
100 Braced girder 5 1/2" 11hole - double open 14
102 Single bent strip 2
103f Flat girder 2 1/2" 5hole 2
108 Architrave (Corner Gusset) 4
109 Face plate 2 1/2"d 1
110 Rack strip 3 1/2" 2
111 Bolt 3/4" 3
112 47Large bent strip 2 1/2x1 1/2" 2
112a 47aLarge bent strip 3x1 1/2" 2
115 Threaded pin - Round Shoulder 2
123 Cone pulley 1
125 Reverse angle bracket 1/2" 4
126a Flat trunnion 5
128 Bell Crank with boss 1
130 Eccentric, Triple Throw 2
134 Crank shaft 1" stroke 1
135 Theodolite protractor 1

NOTES

1. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & foured flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

2. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.