Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 6 (1922-23)

Compiled by Timothy Edwards


 
 
Outfit 6 (1922-23)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 48
1a Perforated strip 9 1/2" 19hole 2
2 Perforated strip 5 1/2" 11hole 50
2a Perforated strip 4 1/2" 9hole 4
3 Perforated strip 3 1/2" 7hole 18
4 Perforated strip 3" 6hole 24
5 Perforated strip 2 1/2" 5hole 36
6 Perforated strip 2" 4hole 24
6a Perforated strip 1 1/2" 3hole 14
8 Angle girder 12 1/2" 25hole 24
8a Angle girder 9 1/2" 19hole 4
9 Angle girder 5 1/2" 11hole 16
9d Angle girder 2 1/2" 5hole 1
10 Flat Bracket (Fishplate) 16
11 Double Angle Bracket 16
12 Angle bracket 80
12a Angle bracket 1x1" 4
12b Angle bracket 1x1/2" 2
13 Axle rod 11 1/2" 4
13a Axle rod 8" 4
14 Axle rod 6" 4
15 Axle rod 5" 4
15a Axle rod 4 1/2" 5
16 Axle rod 3 1/2" 5
16a Axle rod 2 1/2" 2
17 Axle rod 2" 5
18a Axle rod 1 1/2" 4
19 19s/19hCrank Handle - (length varied 3 1/2" - 5") 3
19a Spoked Wheel 3", with boss 4
19b Pulley 3" dia, 2
20 Flanged wheel 1 1/8" dia 8
21 Pulley 1 1/2" dia 2
22 Pulley 1" dia 5
22a Pulley 1" dia without boss 4
23 23bPulley 1/2" dia without boss - metal 8
24 Bush wheel 1 3/8" dia, 8 holes 5
25 Pinion 3/4"dia, 1/4"face, 25t 2
26 Pinion 1/2"dia, 1/4"face, 19t 6
27 Gear wheel 1 1/4"dia, 50t 1
27a Gear wheel 1 1/2"dia,57t 3
28 Contrate Gear 1 1/2" dia, 50t 2
29 Contrate Gear 3/4" dia, 25t 2
32 Worm Gear 2
33 Pawl (type 2) with Pivot Bolts 1
34 Spanner 2
35 Spring clip 24
36 Screwdriver - Standard Bent Rod 1
36a Screwdriver - Extra Long (wooden handle) 1
37 Square Nut and bolt (bolt 5/16" long) 300
38 Washer 3/8" dia. 30
40 Hank of cord 6
41 Propeller Blade - type 1 (wide) 4
43 Tension Spring 2" 2
44 Cranked bent strip 1
45 Double bent strip 8
46 Double angle strip 2 1/2x1" 4
50 Eye piece without boss 2
52 Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) 7
52a Flat plate 5 1/2x3 1/2" 2
53 Flanged plate 3 1/2x2 1/2" 8
53a Flat plate 4 1/2x2 1/2" 1
54 Flanged sector plate 4" 4
57 Wire Hook 2
57b Loaded Hook (large) - ball type 1
58 Spring cord 40" 1
59 Collar 18
60 48aBent strips 2 1/2" 16
60a 48Bent strips 1 1/2" 2
60b 48bBent strips 3 1/2" 6
60c 48dBent strips 5 1/2" 7
61 Windmill sail 4
62 Crank 3
62a Threaded Crank 1
63 Coupling 9
65 Centre fork 1
70 Flat plate 5 1/2x2 1/2" 3
72 Flat plate 2 1/2x2 1/2" 2
76 Trangular plate 2 1/2" 1
77 Trangular plate 1" 2
80a Screwed rod 3 1/2" 1
81 Screwed rod 2" 1
89 Curved strip 5 1/2", 10"r 4
90 Curved strip 2 1/2", 2 3/8"r 6
94 Sprocket chain 8ft
95 Sprocket wheel 2"d, 36t 3
95a Sprocket wheel 1 1/2"d, 28t 1
96 Sprocket wheel 1"d, 18t 4
96a Sprocket wheel 3/4"d, 14t 1
97 Braced girder 3 1/2" 7hole - double open 4
98 Braced girder 2 1/2" 5hole - double open 8
99 Braced girder 12 1/2" 25hole -double open 8
100 Braced girder 5 1/2" 11hole - double open 14
102 Single bent strip 2
103f Flat girder 2 1/2" 5hole 2
108 Architrave (Corner Gusset) 4
109 Face plate 2 1/2"d 1
110 Rack strip 3 1/2" 2
111 Bolt 3/4" 3
112 47Large bent strip 2 1/2x1 1/2" 2
112a 47aLarge bent strip 3x1 1/2" 2
115 Threaded pin - Round Shoulder 2
123 Cone pulley 1
125 Reverse angle bracket 1/2" 4
126a Flat trunnion 5
128 Bell Crank with boss 1
130 Eccentric, Triple Throw 2
134 Crank shaft 1" stroke 1
135 Theodolite protractor 1

NOTES

1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.

2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.