Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 3 (1930)

Compiled by Timothy Edwards


 
 
Outfit 3 (1930)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 10
2 Perforated strip 5 1/2" 11hole 18
3 Perforated strip 3 1/2" 7hole 6
4 Perforated strip 3" 6hole 2
5 Perforated strip 2 1/2" 5hole 12
6a Perforated strip 1 1/2" 3hole 2
8 Angle girder 12 1/2" 25hole 8
10 Flat Bracket (Fishplate) 8
11 Double Angle Bracket 4
12 Angle bracket 14
12a Angle bracket 1x1" 4
13 Axle rod 11 1/2" 1
15 Axle rod 5" 2
15a Axle rod 4 1/2" 3
16 Axle rod 3 1/2" 4
17 Axle rod 2" 2
18a Axle rod 1 1/2" 4
19 19hCrank handle - large (5") 1
19b Pulley 3" dia, 4
19s Crank handle - small (3 1/2") 1
20a Pulley 2" dia 2
20b Flanged wheel 3/4" dia] 4
21 Pulley 1 1/2" dia 1
22 Pulley 1" dia 4
22a Pulley 1" dia without boss 2
23 23bPulley 1/2" dia without boss - metal 1
24 Bush wheel 1 3/8" dia, 8 holes 1
26 Pinion 1/2"dia, 1/4"face, 19t 2
27a Gear wheel 1 1/2"dia,57t 1
32 Worm Gear 1
34 Spanner 1
35 Spring clip 14
36 Screwdriver - Standard Bent Rod 1
37 Square Nut and bolt (bolt 7/32" long) 94
37a Square Nut 6
38 Washer 3/8" dia. 14
40 Hank of cord 3
43 Tension Spring 2" 1
44 Cranked bent strip 1
45 Double bent strip 2
46 Double angle strip 2 1/2x1" 1
48 Double angle strip 1 1/2x1/2" 2
48a Double angle strip 2 1/2x1/2" 10
48b Double angle strip 3 1/2x1/2" 2
52 Flanged Plate 5 1/2x2 1/2" - 4 flanges (See Note below) 2
53 Flanged plate 3 1/2x2 1/2" 3
54 Flanged sector plate 4" 2
57 Wire Hook 1
59 Collar 4
62 Crank 2
63 Coupling 1
90 Curved strip 2 1/2", 2 3/8"r 2
90a Curved strip stepped, 2 1/2", 1 3/8r 4
98 Braced girder 2 1/2" 5hole - double closed 1
99 Braced girder 12 1/2" 25hole - double closed 2
100 Braced girder 5 1/2" 11hole - double closed 2
111 Bolt 3/4" 2
111c Bolt 3/8" 6
115 Threaded pin - Square Shoulder 2
116 Fork piece, Large 1
116a Fork piece, Small 1
125 Reverse angle bracket 1/2" 4
126 Trunnion 2
126a Flat trunnion 2
147b Pivot Bolt with nuts 1
162 Boiler complete 1
163 Sleeve piece 2
164 Chimney adapter 1
165 Swivel bearing 1
166 End bearing 1
How to use Meccano Parts 1

NOTES

1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.

2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.