Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 5 (1928)

Compiled by Timothy Edwards


 
 
Outfit 5 (1928)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 16
2 Perforated strip 5 1/2" 11hole 26
2a Perforated strip 4 1/2" 9hole 4
3 Perforated strip 3 1/2" 7hole 12
4 Perforated strip 3" 6hole 8
5 Perforated strip 2 1/2" 5hole 36
6 Perforated strip 2" 4hole 4
6a Perforated strip 1 1/2" 3hole 6
8 Angle girder 12 1/2" 25hole 14
8a Angle girder 9 1/2" 19hole 4
9 Angle girder 5 1/2" 11hole 4
9d Angle girder 2 1/2" 5hole 1
10 Flat Bracket (Fishplate) 12
11 Double Angle Bracket 8
12 Angle bracket 36
12a Angle bracket 1x1" 6
13 Axle rod 11 1/2" 2
13a Axle rod 8" 1
14 Axle rod 6 1/2" 3
15 Axle rod 5" 4
15a Axle rod 4 1/2" 5
16 Axle rod 3 1/2" 5
17 Axle rod 2"# 5
18a Axle rod 1 1/2" 4
19 19hCrank handle - large (5") 1
19a Spoked Wheel 3", with boss 4
19b Pulley 3" dia, 4
19s Crank handle - small (3 1/2") 1
20 Flanged wheel 1 1/8" dia 8
20b Flanged wheel 3/4" dia] 8
21 Pulley 1 1/2" dia 2
22 Pulley 1" dia 4
22a Pulley 1" dia without boss 3
23 23bPulley 1/2" dia without boss - metal 3
24 Bush wheel 1 3/8" dia, 8 holes 2
26 Pinion 1/2"dia, 1/4"face, 19t 3
27a Gear wheel 1 1/2"dia,57t 2
28 Contrate Gear 1 1/2" dia, 50t 1
29 Contrate Gear 3/4" dia, 25t 2
32 Worm Gear 1
34 Spanner 2
35 Spring clip 19
36 Screwdriver - Standard Bent Rod 1
36b Screwdriver - Special (steel handled) 1
37 Square Nut and bolt (bolt 7/32" long) 169
37a Square Nut 6
38 Washer 3/8" dia. 24
40 Hank of cord 6
41 Propeller Blade - type 2 2
43 Tension Spring 2" 1
44 Cranked bent strip 1
45 Double bent strip 3
46 Double angle strip 2 1/2x1" 4
47 Double angle strip 2 1/2x1 1/2" 1
47a Double angle strip 3x1 1/2" 2
48 Double angle strip 1 1/2x1/2" 2
48a Double angle strip 2 1/2x1/2" 10
48b Double angle strip 3 1/2x1/2" 6
48d Double angle strip 5 1/2x1/2" 4
50a 50Eye piece with boss 1
52 Flanged Plate 5 1/2x2 1/2" - 4 flanges (See Note below) 4
52a Flat plate 5 1/2x3 1/2" 2
53 Flanged plate 3 1/2x2 1/2" 5
54 Flanged sector plate 4" 3
57 Wire Hook 2
59 Collar 13
61 Windmill sail 4
62 Crank 2
63 Coupling 6
65 Centre fork 1
70 Flat plate 5 1/2x2 1/2" 1
77 Trangular plate 1" 2
80a Screwed rod 3 1/2" 1
89 Curved strip 5 1/2", 10"r 4
90 Curved strip 2 1/2", 2 3/8"r 6
90a Curved strip stepped, 2 1/2", 1 3/8r 4
94 Sprocket chain 40"
95 Sprocket wheel 2"d, 36t 2
96 Sprocket wheel 1"d, 18t 2
98 Braced girder 2 1/2" 5hole - double closed 1
99 Braced girder 12 1/2" 25hole - double closed 4
100 Braced girder 5 1/2" 11hole - double closed 7
102 Single bent strip 2
103f Flat girder 2 1/2" 5hole 2
108 Architrave (Corner Gusset) 2
109 Face plate 2 1/2"d 1
111 Bolt 3/4" 3
111c Bolt 3/8" 6
115 Threaded pin - Square Shoulder 2
116 Fork piece, Large 1
116a Fork piece, Small 1
125 Reverse angle bracket 1/2" 4
126 Trunnion 4
126a Flat trunnion 5
128 Bell Crank with boss 1
130 Eccentric, Triple Throw 2
134 Crank shaft 1" stroke 1
138a 138Ship's funnel - raked 1
147a Pawl with boss 1
147b Pivot Bolt with nuts 1
148 Ratchet wheel 1
159 Circular saw 1
160 Channel bearing 1
162 Boiler complete 1
163 Sleeve piece 2
164 Chimney adapter 1
165 Swivel bearing 2
166 End bearing 1
169 Digger Bucket 1
56c Standard Mechanisms 1

NOTES

1. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & foured flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

2. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.