'Other' Construction and Allied Systems Info & Downloads
Lynx Construction Sets
Lynx metal construction sets were similar to Meccano. It was made in England from 1947 till sometime in the 1950s. It can be divided into three distinct phases A, B & C.
Lynx(a) - 1945-1947
Info from the Metal Constructional Systems Database for LYNX [a]
Certain UK
United Kingdom
1945 to 1947
Steel
5BA (see comment *1)
push fit
----
--
22
9.5 (see comment *2)
3.5 (see comment *3)
---
3.3
Nuts: hexagonal
Bolts: round (slotted)
Steel with a Dull plated finish
(see comment *4)
6.2
5.5
Comments
Sets 1-4 known 12/45 plus LINX sets. New parts including rubber Wheel, & Pulley(s), Flanged Plate(s), longer Strips. *1or 6BA. *2Strip 3/8", Flanged Plate(s) ½", Brackets various. *3Flanged Plate(s) 3.8. *4Nuts often Nickel plated steel. 6BA: Nuts plain brass 5.0 or Nickel plated steel 6.4; Bolts plain brass or steel dull plated/nickel 5.1m.
The MCS document for this system is shown below. It can also be downloaded to your computer if desired here
NOTE : If the MCS document does not appear in the window below, then refresh the page.
The report can be zoomed into, made full screen or downloaded as a pdf document by using the controls provided
Below there are manuals/instructions which can be downloaded by clicking on the appropriate image.
Lynx(b) - 1947-1950
Info from the Metal Constructional Systems Database for LYNX [b]
Certain UK
United Kingdom
1947 to 1950
Steel
5BA (see comment *1)
double-tapped
5BA
39
12.7 (see comment *2)
3.8
3.4
3.3
Nuts: hexagonal
Bolts: round (slotted)
Steel with a Dull plated finish
(see comment *3)
6.2
5.5
Comments
Packets of parts may still be marked LINX. A few parts marked LYNX, some MADE IN ENGLAND. Push-fit rubber Wheel & Pulley. 5x7h Flanged Plate replaced 4x7h. *16BA also known. *2Variations in some Brackets. *3As above.
The MCS document for this system is shown below. It can also be downloaded to your computer if desired here
NOTE : If the MCS document does not appear in the window below, then refresh the page.
The report can be zoomed into, made full screen or downloaded as a pdf document by using the controls provided
Below there are manuals/instructions which can be downloaded by clicking on the appropriate image.
Lynx(c) - 1950 to early/mid 1950s
Info from the Metal Constructional Systems Database for LYNX [c]
Certain UK
United Kingdom
1950 to in production in 1952 (see comment *1)
Steel / Aluminium (Alloy)
5BA
double-tapped
5BA
23
55
12.7 (see comment *2)
3.8
3.4
3.3
Nuts: hexagonal
Bolts: round (slotted)
(probably)
Steel with a Dull plated finish
(probably)
6.2(probably)
5.5(probably)
Comments
New parts: including Gears & 3 holes wide Perforated Plates. Sets 1-6, later 1-7, in larger red boxes. Later also an Electrolynx set, a #4 with a small Motor. Later still parts were made of anodised aluminium & mostly marked. *1Perhaps mid-50s.
The MCS document for this system is shown below. It can also be downloaded to your computer if desired here
NOTE : If the MCS document does not appear in the window below, then refresh the page.
The report can be zoomed into, made full screen or downloaded as a pdf document by using the controls provided
Below there are manuals/instructions which can be downloaded by clicking on the appropriate image.
© 2010-2019 Timothy Edwards